DSLR is a very popular concept among professional and amateur photographers commonly used to describe Digital Single-Lens Reflex cameras. Thanks to its versatility and the quality obtained with these cameras today there are many manufacturers offering support and accessories that system.

The term refers generally to control the amount of flash light emitted by the measuring light when returning to the same flash sensor through the lens. In TTL flash metering it occurs after the shutter has opened -the sensors record the amount of light created flash back to the camera through the lens and flash ( turns off automatically "cooling" ) when you haveproduced an adequate amount of light.

Flash system Canon EOS Inc. - Is the photographic flash mechanism used in Canon EOS SLR cameras, either film or digital 135. The main technologies are known by the names "A-TTL" "E-TTL" and "E-TTL II". These technologies have evolved both in the bodies of EOS cameras and flash units, which are sold under the brand Speedlite.

VDC would be the abbreviation for Volt Direct Current which translated would volts direct current. The idea of ??this type is unidirectional current to the load. Direct current is normally produced by batteries, thermocouples, solar cells and a dynamo electric machine type. The direct current can flow in conductors such as wires, but may also flow through semiconductors, insulators ... In the image: 1 - current per pulse 2 - Direct Current (DC) 3 - Alternating Current (AC) 4 - Variable Current

When calculating the life of a battery it will be necessary to know the number of charge cycles that can be performed until the battery does not begin to lose its capacity.
Depending on the type of battery these charging cycles can vary, the most common being the mobile batteries, manufactured Li-Ion or Li-Po, which have a duration of between 300 and 500 charging cycles according to model and manufacturer.
Once thisE limit we will notice how the battery loses duration of operation, arriving to lose up to 25% of its capacity of load.
At this point it will be necessary to evaluate a battery change.
It should be noted that usage and charging habits can significantly affect battery life. For example, factors such as heat, charge the battery several times a day without it is almost exhausted, etc. Will be affectedits duration.
Therefore, to get the most out of the battery we must know when a full charge cycle is performed, and try to avoid misuse of charge, to increase its useful life.
A charging cycle is considered when the battery has been discharged or its 100% charge has been used.
The manufacturers advise that the charge is never made below the 58% battery, since the battery voltage would not fall so lowTo, so you could end up winning up to 4000 charge cycles.
Tips to increase the life of a battery.

• Avoid extreme heat or cold or very long applications of the device.
• Charge the battery as often as you can.
• Fully discharge the battery from time to time.
• Do not let the battery run out completely before charging.

Below is a table with theDifferent voltages (V), charge cycles (C) and battery percentage (B).

Within the wide range of batteries on the market we can differentiate two large groups, disposable batteries and rechargeable batteries.
Disposable batteries are those that only allow a single use and when they are exhausted they can not be recharged. These batteries can store their energy for years.

Rechargeable batteries are those that can be recharged once exhausted. This type is losing charge when they are storedaccording to voltage. The most common we can find them of 1.2V and 3.7V

As a last point you have to take into account that lithium batteries, Lipo, Life etc. Due to its composition, specific loaders should be used.

Depending on the need for installation and type of base, trolley or chair, we can find various types of fixation. Among the most common we find:

A - Through hole: It has a hole in which a screw or stem is inserted. It is a very simple installation system. Ideal for wheels that should not support a lot of load.
B - Threaded stem: It has a threaded stem or nut, it is fixed to the surface with a nut. It is usually the most used fastening system.
C - Angular plate: They are usually less used fastening systems, they have lateral plates to fix on the base.
D - Plate: It has a rectangular or square plate on its surface, it includes 4 or more fastening holes to the base, it is one of the most common.
E - Smooth stem: The stem without thread is inserted into the female of the base, we can find it in the typical office chairs with wheels, TV furniture etc ...